FS: Megan Racing Products: Gauges, Arms, Mufflers etc.*Pics*

TSC · Posted: Thu May 24, 2007 12:11 pm Post subject:

SPEC_C, $650. I replied to your pm.

gt4tified · Posted: Thu May 24, 2007 2:32 pm Post subject:

A little feedback: The megan springs are a hefty drop at 2" front and 1.75" rear. With spring rates of 300 and 250 respectively you'd expect a close to stock feel.

I'm using these on 15" rims and 205/50/15 tyres and the ride is definitely not harsh/stiff but if anything, a bit on the bouncy side. Before you say that the struts cannot support the spring, I'll let you all know that I bought brand new KYB GR-2 insert cartridges and put them on with the springs. The GR-2 was application specific and are the OEM replacement struts.

I'll probably need to go with 16" or 17" rims and tyres since my exhaust is 3" and I can't go over most humps right now. My HKS barrel sits about 3" from the ground.

All in all, I have not rigourously tested these springs/struts combo on cornering yet since I only got the chance to align & camber (a must when changing springs) last weekend.

Will post more as they are tested.

TSC · Posted: Sat May 26, 2007 4:47 pm Post subject:

gt4tified, I can't comment on why the bounciness is there but I do know that springs need to "break in" before they ride the way they are expected to. I know this too from personal experience as I installed a set on my car and I did get a sort of bouncy ride at first but that was about three weeks ago. I am on my original 14s with 185/55 which can contribute to a bad ride. I don't drive it much but the bounciness is definitly fading away and the ride is getting softer and smoother (compared to the initial). I don't know yet what the final ride would be but personally I am satisfied with where its at now. Cornering is firm. I lean before the car has to.

Again, thanks for the review and keep posting them.

TSC · Posted: Mon May 28, 2007 10:36 am Post subject:

Gauges:
Air/Fuel

Oil Press:

Volts:

Boost:

EGT:

Oil Temp:

Vacuum:

Water Temp:

Gauge Install Pics:

katurbobeast · Posted: Mon May 28, 2007 7:52 pm Post subject:

how much for the AF & VAC gauge?

im looking for a universal adj FPR, do u have?

TSC · Posted: Wed May 30, 2007 11:11 pm Post subject:

katurbobeast, $450 each with 6 months warranty. I am out of FPRs.

TSC · Posted: Fri Jun 01, 2007 9:28 am Post subject:

Remember,
Intercooler piping available in kits or by pieces. In stock are 2.5" and 2.75" pieces.
2.5" straights 18" long = $115. Any bend = $135
2.75" straights 18'' long = $130. Any bend = $150
also available are t-bolt clamps, and various couplers and reducers ranging $35-$60.
Piping can be used to design custom cold air intakes (CAI) or short rams.
Other size kits (2"-3") can be obtained between $1400-$1700. Kits include 8 pcs pipe, couplers and clamps. Inquire by phone or pm.

TSC · Posted: Thu Jun 07, 2007 5:39 am Post subject:

I will be in St. Augustine today. Place orders early for drop-off/delivery between Rio Claro (through link-up San Fernando) and Grand Bazaar.

playaz97 · Posted: Thu Jun 07, 2007 9:06 am Post subject:

TSC, i still waiting on the UPPER REAR STRUT BAR for my 99-00 HONDA CIVIC

wassup wid dat?

7892118 sherwin

its been like 4eva now Shocked

playaz97 · Posted: Thu Jun 07, 2007 9:07 am Post subject:

TSC, i still waiting on the UPPER REAR STRUT BAR for my 99-00 HONDA CIVIC

wassup wid dat?

7892118 sherwin

its been like 4eva now Shocked

Kronik · Posted: Thu Jun 07, 2007 1:17 pm Post subject:

that probably coming in the next shipment.........hopefully megan send mines too Mr. Green

TSC · Posted: Sat Jun 09, 2007 1:56 am Post subject:

playaz97,Kronik, those were backordered. I do apologise for the long wait. You are not alone.

TSC · Posted: Sun Jun 10, 2007 12:14 pm Post subject:

Sale on MX-6 / 626 RU bars. $250 + Delivery.

sr20ve · Posted: Sun Jun 10, 2007 3:07 pm Post subject:

PM me a list of suspension mod u have for the Z32 300zx also if u have pullies

TSC · Posted: Mon Jun 11, 2007 8:54 pm Post subject:

sr20ve, pm sent.

TSC · Posted: Wed Jun 13, 2007 1:23 am Post subject:

Remember,
Intercooler piping available in kits or by pieces. In stock are 2.5" and 2.75" pieces.
2.5" straights 18" long = $115. Any bend = $135
2.75" straights 18'' long = $130. Any bend = $150
also available are t-bolt clamps, and various couplers and reducers ranging $35-$60.
Piping can be used to design custom cold air intakes (CAI) or short rams.
Other size kits (2"-3") can be obtained between $1400-$1700. Kits include 8 pcs pipe, couplers and clamps. Inquire by phone or pm.

nismotrinidappa · Posted: Wed Jun 13, 2007 5:12 am Post subject:

whats your price on 1st gen rx 7 coilovers strut bars front and back and a/f, boost gyage and dual a pillar pod

TRDGUY · Posted: Wed Jun 13, 2007 6:52 am Post subject:

could you link me up with a lightened pulley for the 3zzfe engine ?

TRDGUY · Posted: Wed Jun 13, 2007 10:05 am Post subject:

hello is it possible to obtain a lighten pulley for the 3zzfe engine ?? if so i want one .thanks

TSC · Posted: Wed Jun 13, 2007 11:07 am Post subject:

nismotrinidappa, for coilovers you have to call me. Front and rear bars will be $580 for pair (if in stock). Gauges are $450 each with warranty.

TRDGUY, I only have pulleys for civic, lancer and most sr20 cars. No Toyotas yet.