| View previous topic :: View next topic |
| Author
|
Message |
idlemind TriniTuner WHOoRE
Joined: 15 Aug 2005 Tech posts: 1412 Location: Shifting with no clutching My 2NRide: Mitsubishi Touring Lancer
|
Posted: Wed Mar 25, 2009 10:40 am Post subject: |
|
|
may not be related or it may.
do the usual, flush the tranny and replace the oil.
i did a 360 on the highway and the car was fine. |
|
| Back to top |
|
 |
|
|
 |
P3UNG 3NE 2NR for life
Joined: 24 Nov 2008 Tech posts: 135 Location: Trinidad My 2NRide: Mitsubishi Lancer
|
Posted: Wed Mar 25, 2009 11:04 am Post subject: |
|
|
seen...well he spin straight into a ditch at the side of the highway...had to get towed cause the front was bumper deep in mud...
360 on the highway....whey! you playin knight rider...!!  |
|
| Back to top |
|
 |
idlemind TriniTuner WHOoRE
Joined: 15 Aug 2005 Tech posts: 1412 Location: Shifting with no clutching My 2NRide: Mitsubishi Touring Lancer
|
Posted: Wed Mar 25, 2009 11:13 am Post subject: |
|
|
was some scary sheit
wet road, 120kmh, got bad drive, non-abs integra, applied for brakes and when i released, chaos ensued, went into a ditch as well but i was able to drive out.
he checked under the car for visible signs of damage?
tranny on the leftside eh |
|
| Back to top |
|
 |
P3UNG 3NE 2NR for life
Joined: 24 Nov 2008 Tech posts: 135 Location: Trinidad My 2NRide: Mitsubishi Lancer
|
Posted: Wed Mar 25, 2009 11:49 am Post subject: |
|
|
well as far as he say...it look ok, no visible signs...only thing is the plastic stone shield below need to replace or get clips.
well it was raining too when the car run off the road into the ditch... it was all mud so i guess that saved it from underbody damage... |
|
| Back to top |
|
 |
idlemind TriniTuner WHOoRE
Joined: 15 Aug 2005 Tech posts: 1412 Location: Shifting with no clutching My 2NRide: Mitsubishi Touring Lancer
|
Posted: Wed Mar 25, 2009 12:08 pm Post subject: |
|
|
Thing is the most DIY you can do with a tranny is change the fluid.
Anything other than that is to go inside.
I can give u a place named Jenton on Aranguez main road he can make an appointment. but anything to go inside a tranny is real paper. |
|
| Back to top |
|
 |
P3UNG 3NE 2NR for life
Joined: 24 Nov 2008 Tech posts: 135 Location: Trinidad My 2NRide: Mitsubishi Lancer
|
Posted: Wed Mar 25, 2009 2:11 pm Post subject: |
|
|
seen...well is worth a mention to him, prevention is better than cure..hehe!  |
|
| Back to top |
|
 |
venum 3NE2NR Diesel Boyz
Joined: 07 May 2004 Tech posts: 3832 Location: San Fernando My 2NRide: Mitsubishi L200 Animal
|
Posted: Wed Mar 25, 2009 5:00 pm Post subject: |
|
|
| P3UNG wrote: | | p.s. oh... is a cs lancer |
if it wasn't yuh would have to
the delay in gear changes can be solved with a good tranny fluid change
if yuh have to repair - buy another, it cheaper
as for teh ralliart CS5, i don't think that it is teh same one with the OZ rally decals
that one from Princes Town |
|
| Back to top |
|
 |
P3UNG 3NE 2NR for life
Joined: 24 Nov 2008 Tech posts: 135 Location: Trinidad My 2NRide: Mitsubishi Lancer
|
Posted: Wed Mar 25, 2009 6:30 pm Post subject: |
|
|
well is a DM cs3 about 6mths...so i doh think he wanna hear bout repairing or buyin another.
thnx on the info.. |
|
| Back to top |
|
 |
ronsin1 I LUV THIS PLACE
Joined: 30 Nov 2005 Tech posts: 1073 Location: lookin' for meh PNM Party Card My 2NRide: Mitsubishi Lancer
|
Posted: Wed Mar 25, 2009 6:54 pm Post subject: |
|
|
| venum wrote: | | P3UNG wrote: | | p.s. oh... is a cs lancer |
if it wasn't yuh would have to
the delay in gear changes can be solved with a good tranny fluid change
if yuh have to repair - buy another, it cheaper
as for teh ralliart CS5, i don't think that it is teh same one with the OZ rally decals
that one from Princes Town |
oh yes it is the decals were stripped out |
|
| Back to top |
|
 |
venum 3NE2NR Diesel Boyz
Joined: 07 May 2004 Tech posts: 3832 Location: San Fernando My 2NRide: Mitsubishi L200 Animal
|
Posted: Thu Mar 26, 2009 8:44 am Post subject: |
|
|
| ^^^ i mean the one i saw |
|
| Back to top |
|
 |
ronsin1 I LUV THIS PLACE
Joined: 30 Nov 2005 Tech posts: 1073 Location: lookin' for meh PNM Party Card My 2NRide: Mitsubishi Lancer
|
Posted: Thu Mar 26, 2009 10:42 am Post subject: |
|
|
sorry |
|
| Back to top |
|
 |
turbo_beast369 Chronic TriniTuner
Joined: 20 Jan 2006 Tech posts: 542 Location: Sando My 2NRide:
|
Posted: Tue Mar 31, 2009 3:00 pm Post subject: |
|
|
| is there any need to adjust the tappets on a 4G18 from a 2003 CS3 doing 114,000 KM. There is nothing wrong with the engine, no noise really. Do u think it is recommended at that relatively high mileage? |
|
| Back to top |
|
 |
R@lli@rt Sweet on this forum
Joined: 31 Oct 2006 Tech posts: 277 Location: st augustine My 2NRide:
|
Posted: Tue Mar 31, 2009 3:18 pm Post subject: |
|
|
Fellas, i now reach page 20....
Just saying hi and i learning real plenty
I sold the cs2a and getting a cs3, 4g18, cannot wait...to start playing
Aye, i still playing catch-up in many ways!!! Had a ck, then a cs2 now a cs3 and well, hopefully a cy next!
I just got tired reading really, ok, i going back to page 20 now, laters guys!  |
|
| Back to top |
|
 |
idlemind TriniTuner WHOoRE
Joined: 15 Aug 2005 Tech posts: 1412 Location: Shifting with no clutching My 2NRide: Mitsubishi Touring Lancer
|
Posted: Tue Mar 31, 2009 3:28 pm Post subject: |
|
|
| jus skip all venum's posts they really not substantial |
|
| Back to top |
|
 |
rainman Chronic TriniTuner
Joined: 25 Jul 2005 Tech posts: 576 Location: Planning to puh dong a wuk! My 2NRide: De Lorean DMC-12
|
Posted: Tue Mar 31, 2009 4:40 pm Post subject: |
|
|
| idlemind wrote: | | jus skip all venum's posts they really not substantial |
 |
|
| Back to top |
|
 |
venum 3NE2NR Diesel Boyz
Joined: 07 May 2004 Tech posts: 3832 Location: San Fernando My 2NRide: Mitsubishi L200 Animal
|
Posted: Tue Mar 31, 2009 4:43 pm Post subject: |
|
|
Ms. R@lli@rt, firstly . . . nice avatar
secondly, now that we have CS3's can we expect you to be posting technical in this thread
frankly we\I have gotten used to and tired of Idlemind's feminity and would welcome any new girl's perspective contributions
no girly stuff plz, that is what we have Idlemind for, he's just been providing entertainment . . .
Idle - next time yuh break something . . . |
|
| Back to top |
|
 |
ronsin1 I LUV THIS PLACE
Joined: 30 Nov 2005 Tech posts: 1073 Location: lookin' for meh PNM Party Card My 2NRide: Mitsubishi Lancer
|
Posted: Tue Mar 31, 2009 6:26 pm Post subject: |
|
|
| ^^^ break something or looking for a bumper |
|
| Back to top |
|
 |
venum 3NE2NR Diesel Boyz
Joined: 07 May 2004 Tech posts: 3832 Location: San Fernando My 2NRide: Mitsubishi L200 Animal
|
Posted: Tue Mar 31, 2009 8:15 pm Post subject: |
|
|
aye, i forget to check that for him yess
thanx for reminding me |
|
| Back to top |
|
 |
idlemind TriniTuner WHOoRE
Joined: 15 Aug 2005 Tech posts: 1412 Location: Shifting with no clutching My 2NRide: Mitsubishi Touring Lancer
|
Posted: Tue Mar 31, 2009 9:29 pm Post subject: |
|
|
steupss but allyuh know allyuh is the worse
couldnt even ask me if i gettin thru with the repairs self.
anyway the bumper not bad, it repairable.
as for the lights....wait til allyuh see the concoction
so venum, nevermind looking u were useless anyway
...and stop answering the phone with "wuh yuh mashup now"
rainman, u get ronsin1's permisson to post his pic?
R@lli@rt make sure and walk with the new CS @ Dex  |
|
| Back to top |
|
 |
ronsin1 I LUV THIS PLACE
Joined: 30 Nov 2005 Tech posts: 1073 Location: lookin' for meh PNM Party Card My 2NRide: Mitsubishi Lancer
|
Posted: Tue Mar 31, 2009 9:48 pm Post subject: |
|
|
wait wait wait what pic alyuh talking about  |
|
| Back to top |
|
 |
QG 30 pounds of Boost
Joined: 18 Jul 2006 Tech posts: 2584 Location: Cross-Crossing, San Fernando My 2NRide: Nissan Y11 AD WAGON
|
Posted: Tue Mar 31, 2009 11:27 pm Post subject: |
|
|
LMAO...  |
|
| Back to top |
|
 |
rainman Chronic TriniTuner
Joined: 25 Jul 2005 Tech posts: 576 Location: Planning to puh dong a wuk! My 2NRide: De Lorean DMC-12
|
Posted: Tue Mar 31, 2009 11:33 pm Post subject: |
|
|
| Quote: |
rainman, u get ronsin1's permisson to post his pic?
|
sorry ronsin. no hard feelings? |
|
| Back to top |
|
 |
ronsin1 I LUV THIS PLACE
Joined: 30 Nov 2005 Tech posts: 1073 Location: lookin' for meh PNM Party Card My 2NRide: Mitsubishi Lancer
|
Posted: Wed Apr 01, 2009 6:15 am Post subject: |
|
|
| no hard feelings dude My pic was already posted on this site |
|
| Back to top |
|
 |
R@lli@rt Sweet on this forum
Joined: 31 Oct 2006 Tech posts: 277 Location: st augustine My 2NRide:
|
Posted: Wed Apr 01, 2009 9:00 am Post subject: |
|
|
venum, ty, it's a reminder of how stress free i used to be at one point in my life, lol...so yeah it's one of my fav pics
And yes, will definitely be learning and trying to help/contribute where i can!
idlemind, lol, y'all not easy nah! As soon as the car gets here will bring it for you guys to see it, cannot wait to finish reading about y'all previous posts so i can get ideas as to what little mods i want to do.
I like the short ram mod that was done, i already looked at the amount of space to spare in the engine bay and i found it much roomier than the cedia, that's nice. I may have a question here and there when the car actually gets here, so warning in advance! Def gonna have the tranny and oil cooler done, asap.
ronsin1, like your avatar, you the original fozzy bear! |
|
| Back to top |
|
 |
idlemind TriniTuner WHOoRE
Joined: 15 Aug 2005 Tech posts: 1412 Location: Shifting with no clutching My 2NRide: Mitsubishi Touring Lancer
|
Posted: Wed Apr 01, 2009 9:08 am Post subject: |
|
|
case in point...he installed the short RAM intake and by the next week he pulled it off and scrapped the idea........see not substantial
you will get more room in the 4g18 coz of the mere fact that its a SOHC as opposed to the DOHC GDI in the Cedia...meaning the top part of the engine (head) not as wide. I addition to that, the 4g18 doesnt have the chunky engine cover like the GDI.
the main issue with the aftermarkt intake is getting clean air in and not recycling hot air from the tranny. seal off the bottom and the engine sides of the filter and u may be good to go.
for more ideas as to what can be done, visit QG's "Monster CS" thread |
|
| Back to top |
|
 |
R@lli@rt Sweet on this forum
Joined: 31 Oct 2006 Tech posts: 277 Location: st augustine My 2NRide:
|
Posted: Wed Apr 01, 2009 9:33 am Post subject: |
|
|
he scraped the idea?! how come? where is he?
lol...
ok, will check the "Monster CS" thread for sure!!! |
|
| Back to top |
|
 |
idlemind TriniTuner WHOoRE
Joined: 15 Aug 2005 Tech posts: 1412 Location: Shifting with no clutching My 2NRide: Mitsubishi Touring Lancer
|
Posted: Wed Apr 01, 2009 9:39 am Post subject: |
|
|
i'll leave it for him to explain, my response mite sound too feminine
like it was too long or it started to rub and cause discomfort....
wey venum ? |
|
| Back to top |
|
 |
R@lli@rt Sweet on this forum
Joined: 31 Oct 2006 Tech posts: 277 Location: st augustine My 2NRide:
|
Posted: Wed Apr 01, 2009 9:41 am Post subject: |
|
|
idlemind! lmao!!!
lol, yeah, i wanna know why venum took off the intake...cuz am thinking of getting one put on... |
|
| Back to top |
|
 |
QG 30 pounds of Boost
Joined: 18 Jul 2006 Tech posts: 2584 Location: Cross-Crossing, San Fernando My 2NRide: Nissan Y11 AD WAGON
|
|
| Back to top |
|
 |
R@lli@rt Sweet on this forum
Joined: 31 Oct 2006 Tech posts: 277 Location: st augustine My 2NRide:
|
Posted: Wed Apr 01, 2009 10:35 am Post subject: |
|
|
thanks QG,  |
|
| Back to top |
|
 |
|
|
|